Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

多梁复合结构的动力学建模及全局解析振型分析

多梁复合结构广泛用于工程领域，其动力学特性对相关装备的工作状况有着重要影响，建立准确适用的动力学模型对后续的动力学响应参数影响规律研究有决定性作用。针对工程中常见的多梁复合结构，给出了位移场的一般表达式，利用哈密顿原理得出多梁复合结构的运动控制方程和边界条件，对其全局解析振型进行理论计算，给出了计算多梁复合结构数值振型的一般过程，基于数值分析和实验分析以L型梁和Z型梁为例利用频率相对误差、振型定性比较和MAC定量分析说明了全局解析振型的求解验证方法，利用伽辽金方法和全局解析振型给出了截断原系统得到离散系统运动方程的一般形式。提出的多梁复合结构的建模方法和全局解析振型求解验证方法，对工程中此类结构动力学响应的参数影响规律研究有重要意义。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

虚拟环境系统中复杂模型的建立--3D资源在快速开发虚拟环境系统中的应用

对利用3D资源在快速开发虚拟环境系统中的方法进行了研究。在开发虚拟环境系统的过程中，复杂模型的建立是必不可少的，仅仅利用OpenGL函数编程来实现仿真是很困难的，针对该问题提出了利用3D资源进行3D文件读取和转换的两种方案，分析了虚拟环境中复杂模型的建立以及处理的基本方法，并对数控车床的仿真进行了详细介绍。     

Global Response of Martian Plasma Environment to an Interplanetary Structure: From Ena and Plasma Observations at Mars

As a part of the global plasma environment study of Mars and its response to the solar wind, we have analyzed a peculiar case of the subsolar energetic neutral atom (ENA) jet observed on June 7, 2004 by the Neutral Particle Detector (NPD) on board the Mars Express satellite. The “subsolar ENA jet” is generated by the interaction between the solar wind and the Martian exosphere, and is one of the most intense sources of ENA flux observed in the vicinity of Mars. On June 7, 2004 (orbit 485 of Mars Express), the NPD observed a very intense subsolar ENA jet, which then abruptly decreased within ∼10 sec followed by quasi-periodic (∼1 min) flux variations. Simultaneously, the plasma sensors detected a solar wind structure, which was most likely an interplanetary shock surface. The abrupt decrease of the ENA flux and the quasi-periodic flux variations can be understood in the framework of the global response of the Martian plasma obstacle to the interplanetary shock. The generation region of the subsolar ENA jet was pushed towards the planet by the interplanetary shock; and therefore, Mars Express went out of the ENA jet region. Associated global vibrations of the Martian plasma obstacle may have been the cause of the quasi-periodic flux variations of the ENA flux at the spacecraft location.     

复合材料面内剪切Iosipescue方法分析及试验研究

讨论了采用双Ｖ形开槽试样的Ｉｏｓｉｐｅｓｃｕ剪切试验方法的应用，分析了影响试验的因素，对Ｔ３００／５２２２复合材料单向板及π／４多向铺层层合板进行了试验研究。试验结果表明，此方法可以很好地用于复合材料剪切试验。     

Tunnel/predictor display with two-axis control coordination and simplification

A longitudinal-lateral control coordination and simplification concept is considered for a tunnel/predictor display, which presents the command flight path and a specified future aircraft position in a 3-dimensional format to the pilot, for improving flight path control. A basic element of the proposed concept is the generation of common longitudinal-lateral transfer characteristics of the predictor-aircraft system for the crossover frequency region. Control coordination is supported by a dynamics similarity between the longitudinal and the lateral response characteristics of the predictor position in closed-loop pilot control actions. The control coordination and simplification concept is considered to support the pilot in manual flight path control, directed at an enhancement of his control performance and at a reduction of his workload. Results from pilot-in-the-loop simulation experiments support the theoretical findings and show the effectiveness of the proposed predictor concept with control coordination.     

门限自回归模型参数的局部正交设计寻优法

在采用点值图确定门限区间个数的基础上，对门自回归模型中门限值、滞后步长、各门限区间模型阶数，利用正交设计方法寻优，计算工作量锐减，却可得到精度较高的预报模型。